GPU Support Bracket, 2.75-4.52Inch GPU Sag Bracket with Non-Slip Sheet, GPU Holder for Prevent Graphics Card Sag (Black)
Want the best price and purchase timing?
Our AI advisor analyzes real-time pricing across all channels to find you the best deal.
AI Verdict
It is a $10 aluminum pillar that stops your massive RTX 4090 from snapping your motherboard in half, provided your case gap is exactly between 2.75 and 4.52 inches.
This bracket depends entirely on the physical distance between your GPU and your case floor. It works flawlessly if your gap falls within the 2.75 to 4.52-inch window and you have a flat steel surface for the magnet. It becomes a useless paperweight if your gap is 5 inches.
If your case floor is lower, buy a 74-120mm (2.9-4.7 inch) tall bracket or a PCIe-mounted brace.
Regret Score™
Medium RiskLower is better — measures purchase-regret risk from real buyer complaints, review credibility, and product maturity
Issues discovered after purchase
Critically weak dimension
Amazon rating vs actual quality
Chance this product isn't for you
Pros
- Anodized aluminum construction supports 4.5-pound GPUs without bending.
- Magnetic base grabs onto steel PSU shrouds to stop the 35g pillar from sliding during desk bumps.
- Rubber pads on both ends prevent metal-on-metal scratching against the plastic GPU shroud.
- Threaded screw mechanism allows for millimeter-precise height adjustments between 2.75 and 4.52 inches.
Cons
- The 4.52-inch maximum height fails to reach GPUs in bottom-intake cases like the O11 Dynamic.
- The thin locking nut is difficult to tighten with fingers in cramped micro-ATX cases.
- Magnet only grips steel — it relies entirely on gravity if you have an aluminum chassis or plastic shroud.
Dimension Scores
Prevents a heavy 3-slot GPU from ripping out the PCIe slot, ensuring the system actually boots to play games.
The slim 15mm diameter shaft blocks zero airflow from bottom intake fans compared to bulky vertical mounts.
It is a passive piece of aluminum that draws 0 watts.
It is a solid metal stick with exactly 0GB of VRAM.
Best For
- Standard ATX mid-towers with a flat metal PSU shroud directly under the GPU
- Heavy triple-slot cards like the RTX 4080 or RX 7900 XTX that sag heavily on the right edge
- Builds where you want to hide the support bracket behind power cables
Not Recommended For
- Dual-chamber cases like the Lian Li O11 where the floor is too far from the GPU
- Cases with angled or heavily vented plastic PSU shrouds that prevent a flat magnetic grip
Watch Out For
- Measure your exact gap before buying — if your GPU sits 5 inches above the shroud, this 4.52-inch bracket does absolutely nothing.
- The base magnet is weak on mesh surfaces and requires a solid flat piece of steel to bite down.
- You must place the top rubber pad exactly on the plastic GPU frame without blocking a spinning fan blade.
Full Specifications
| ASIN | B0B2WCTGFV |
| Brand | Ausvrkkit |
| Color | Black |
| Material | Aluminum |
| Item Depth | 4.52 Inches |
| Unit Count | 1.0 Count |
| Finish Type | Anodized |
| Item Weight | 4 ounces |
| Manufacturer | Ausvrkkit |
| Mounting Type | Chassis Mount |
| Item model number | 02fe7797-9846-468c-bfd2-9d43af2e6656 |
| Package Dimensions | 5.56 x 1.97 x 0.55 inches |
What Buyers Say
A massive chunk of 1-star reviews come from people who didn't use a tape measure before ordering. The 4.52-inch max height is physically too short for cases with bottom intake fans or missing PSU shrouds. When the gap actually matches the specs, the threaded adjustment provides infinitely more precise leveling than peg-hole brackets. The base magnet grips bare steel well, but multiple forum posts mention it fails to hold onto heavily perforated mesh shrouds or thick case paint.
“Works great but I am an idiot and didn't measure my case first so it was half an inch too short, had to put a stack of pennies under it.”
Common Praise
- Threaded design allows for exact millimeter height matching
- Anodized black finish blends in perfectly with dark PC builds
- Rubber pads successfully prevent vibration noise against the GPU cooler
- Takes less than 30 seconds to install without any tools
Common Complaints
- Max height of 4.52 inches is too short for many modern dual-chamber cases
- Base magnet is too weak to hold onto heavily perforated PSU shrouds
- Locking nut is thin and hard to grip if you have large fingers
- Top pad is small and requires careful placement to avoid hitting GPU fan blades
Ownership Tips
- The locking ring vibrates loose over a few months if you don't tighten it down hard.
- Dust collects heavily on the exposed threads of the screw mechanism.
- Moving your PC to clean it usually tips the bracket over, requiring a reset.
Frequently Asked Questions
Will this fit in a Lian Li O11 Dynamic?
Probably not. The O11 usually has bottom fans, meaning the gap from the fan hub to the GPU is often taller than 4.52 inches.
Does the magnet damage hard drives?
No. The magnet in the base is very weak and only meant to stop the 35g aluminum stick from tipping over.
How do I lock the height?
Twist the main shaft to the height you need, then spin the middle locking nut down until it tightens against the base.
Can I use this on a plastic PSU shroud?
Yes, but the magnet won't work. You have to rely on the rubber base pad and the downward pressure of the GPU to keep it in place.
Will the metal scratch my graphics card?
No. The top contact point has a silicone washer that sits between the aluminum bracket and your GPU cooler.
Buying Guide
You are buying a tiny metal kickstand for your graphics card. The only thing that matters is the physical distance between your GPU and the floor of your case. Grab a ruler, stick it under the sagging corner of your graphics card, and measure down to the metal shroud below it. Buy this if that number is strictly between 2.75 and 4.52 inches.
2.75 - 4.52 Inch Range
This is the minimum and maximum height the screw can reach. Think of it like a car jack — if your car is lifted 6 inches off the ground, a 4-inch jack won't touch it.
Magnetic Base
Helps the pillar stick to the steel floor of your PC case so it doesn't get knocked over when you bump your desk.
Anodized Aluminum
Provides enough structural strength to hold a 5-pound graphics card without bending, and the black coating resists chipping.
Alternatives
Search for a 'tall GPU support bracket' if your gap is larger than 4.5 inches, or a 'PCIe slot GPU brace' if bottom case fans block the floor.
You Might Also Like
HP NVIDIA GeForce RTX 3070 8GB OEM Graphics Card (Renewed)
$150-$299This is a renewed HP OEM NVIDIA GeForce RTX 3070 with 8GB VRAM, a gamble for budget-conscious 1440p gamers who understand the risks of refurbished hardware.
ZOTAC Gaming GeForce RTX 5070 Twin Edge OC DLSS 4 12GB GDDR7 192-bit 28 Gbps PCIE 5.0 Gaming Graphics Card, IceStorm 2.0 Cooling, SFF-Ready, ZT-B50700H-10A
$600+This is a 2-slot, SFF-ready NVIDIA RTX 5070 with 12GB GDDR7 and a 2542 MHz boost clock, built for compact gaming rigs needing high 1440p performance.
ZOTAC Gaming GeForce RTX 5080 Solid CORE OC DLSS 4 16GB GDDR7 256-bit 30 Gbps PCIE 5.0 Gaming Graphics Card, IceStorm 3.0 Advanced Cooling, Spectra RGB Lighting, ZT-B50800J2-10A
$600+This ZOTAC RTX 5080 with 16GB GDDR7 and a 2640 GHz clock speed is built for high-end 4K gaming and content creation on the NVIDIA Blackwell architecture.
ZOTAC Gaming GeForce RTX 5060 Ti 8GB Twin Edge OC DLSS 4 8GB GDDR7 128-bit 28 Gbps PCIE 5.0 Gaming Graphics Card, IceStorm 2.0 Cooling, SFF-Ready, ZT-B50610H-10A
$300-$599This is a compact, 2-slot RTX 5060 Ti with 8GB GDDR7 and a 2602 MHz clock, built for SFF gaming rigs.